Document repeater validation and operating limits
This commit is contained in:
+32
-2
@@ -41,8 +41,15 @@ RX gain: boosted (reg 0x08AC = 0x96)
|
||||
TX params: default -9 dBm configured (min), ramp 40 us; PA config
|
||||
(0x02,0x02,0x00,0x01) = +14 dBm-optimal table, deliberately
|
||||
capped -- the external KCT8103L PA adds gain on top
|
||||
|
||||
```
|
||||
|
||||
PA-row invariant: `deviceSel` must remain `0x00` for SX1262, and the other
|
||||
bytes must come from an SX1262 row. The removed diagnostic
|
||||
`(0x01,0x00,0x00,0x01)` mixed the SX1261 +10 dBm PA-duty/hpMax values with
|
||||
SX1262 selection. This undocumented hybrid reduced measured RF by about
|
||||
32 dB while all chip-side TX diagnostics still passed.
|
||||
|
||||
## Consequences of the fixed-255-byte RX capture
|
||||
|
||||
RxDone fires ~ (255 - frame_len) * 80 us after the actual end of frame;
|
||||
@@ -54,5 +61,28 @@ time per frame. Acceptable for the experiment; optimization candidate
|
||||
## TX power
|
||||
|
||||
Configured SX1262 power is NOT radiated power: the KCT8103L PA follows.
|
||||
Development default is the SX1262 minimum (-9 dBm). Log lines carry
|
||||
`configured_tx_dbm` to keep this distinction explicit.
|
||||
Development default is the SX1262 minimum (-9 dBm), and the console accepts
|
||||
only -9..+2 dBm. +2 is the level used by known-good Heltec V4.3 firmware,
|
||||
not a declaration of legal radiated power. Keep -9 dBm until the complete
|
||||
FEM/antenna path has a conducted or calibrated e.r.p. measurement.
|
||||
|
||||
`wmbus_tx.configured_tx_dbm` records SetTxParams. `airtime_us` is computed
|
||||
channel occupancy (48-bit preamble + 16-bit sync + payload at 100 kbps);
|
||||
`tx_operation_us` is the longer firmware-entry-through-TxDone latency.
|
||||
|
||||
## T-mode (T1) support
|
||||
|
||||
T1 shares the 0x543D access code, so ONE radio configuration receives
|
||||
both modes: C-mode announces itself with two NRZ mode bytes after the
|
||||
sync; T-mode continues directly with 3-of-6 coded data (decoded in
|
||||
software from the same fixed 255-byte capture; wM-Bus C/T share the
|
||||
100 kchip/s rate). Tables verified against rtl-wmbus.
|
||||
|
||||
TX: T1 frames are 3-of-6 encoded in software and sent with 50 kHz FSK
|
||||
deviation (raw 0x00CCCD) instead of C-mode's 45 kHz; the swap is a lazy
|
||||
per-TX SetModulationParams (deviation is a TX-only GFSK parameter, RX is
|
||||
unaffected). Verified: rtl_wmbus decodes our synthetic T1 frames,
|
||||
including L=140.
|
||||
|
||||
Length caps from the fixed 255-byte capture: C1 total <= 253 bytes;
|
||||
T1 total <= 170 decoded bytes (coded 1.5x).
|
||||
|
||||
Reference in New Issue
Block a user