hil: segmented capture with tuner-fault recovery, in-window IQ accounting
This commit is contained in:
+68
-26
@@ -1,40 +1,82 @@
|
||||
#!/usr/bin/env bash
|
||||
# Capture rtl_wmbus decodes AND raw IQ from a SINGLE rtl_sdr stream.
|
||||
# Capture rtl_wmbus decodes AND raw IQ from a single rtl_sdr stream, in
|
||||
# bounded segments with recovery between them.
|
||||
#
|
||||
# Why one stream: this dongle's sensitivity drifts by ~17 dB over minutes,
|
||||
# so measurements taken in separate captures at "the same gain" are not
|
||||
# comparable. Decoding meter originals and measuring our own transmissions
|
||||
# in the IQ must therefore share one stream, one gain, one instant.
|
||||
# Two hardware facts drive this design (docs/FINDINGS.md):
|
||||
# 1. This dongle's R820T tuner dies after a few minutes of continuous
|
||||
# streaming ("r82xx_write: i2c wr failed"). rtl_sdr does NOT exit -- it
|
||||
# keeps producing nothing, so a naive long capture silently goes deaf.
|
||||
# Bounded segments with -n make it exit cleanly, and we usbreset between
|
||||
# segments instead of relying on failure detection.
|
||||
# 2. Sensitivity drifts ~17 dB over minutes, so meter decodes and our own
|
||||
# TX measurements must come from the same stream to be comparable.
|
||||
#
|
||||
# Usage: capture_both.sh DURATION_S DECODE_LOG IQ_FILE [GAIN]
|
||||
# Usage: capture_both.sh DURATION_S DECODE_LOG IQ_FILE [GAIN] [IQ_SEGMENTS]
|
||||
set -euo pipefail
|
||||
cd "$(dirname "$0")/.."
|
||||
DUR=$1; OUT=$2; IQ=$3; GAIN=${4:-42.1}
|
||||
DUR=$1; OUT=$2; IQ=$3; GAIN=${4:-42.1}; IQ_SEGMENTS=${5:-1}
|
||||
|
||||
SEG=${SEG_SECONDS:-140} # below the observed tuner death point
|
||||
RATE=1600000
|
||||
|
||||
: > "$OUT"
|
||||
: > "$IQ"
|
||||
ERR="${OUT%.log}.err"
|
||||
STATS="${OUT%.log}.stats"
|
||||
: > "$ERR"
|
||||
|
||||
health_ok=0
|
||||
for i in 1 2 3; do
|
||||
if ./result-py/bin/python3 hil/sdr_health.py >> "$ERR" 2>&1; then
|
||||
health_ok=1; break
|
||||
health() {
|
||||
./result-py/bin/python3 hil/sdr_health.py >> "$ERR" 2>&1
|
||||
}
|
||||
|
||||
usable=0
|
||||
segments=0
|
||||
recovered=0
|
||||
iq_seconds=0
|
||||
deadline=$(( $(date +%s) + DUR ))
|
||||
|
||||
while :; do
|
||||
remaining=$(( deadline - $(date +%s) ))
|
||||
[ "$remaining" -le 10 ] && break
|
||||
this=$(( remaining < SEG ? remaining : SEG ))
|
||||
segments=$((segments + 1))
|
||||
|
||||
if ! health; then
|
||||
echo "--- segment $segments: SDR unhealthy, usbreset" >> "$ERR"
|
||||
usbreset 0bda:2838 >> "$ERR" 2>&1 || true
|
||||
recovered=$((recovered + 1))
|
||||
sleep 5
|
||||
health || { echo "--- still unhealthy, skipping segment" >> "$ERR"; sleep 2; continue; }
|
||||
fi
|
||||
|
||||
echo "--- segment $segments: ${this}s (gain $GAIN)" >> "$ERR"
|
||||
t0=$(date +%s)
|
||||
if [ "$segments" -le "$IQ_SEGMENTS" ]; then
|
||||
# keep IQ for the first segments only; bounded so disk use is known
|
||||
timeout $((this + 20)) rtl_sdr -f 868950000 -s "$RATE" -g "$GAIN" \
|
||||
-n $((this * RATE)) - 2>>"$ERR" \
|
||||
| tee -a "$IQ" \
|
||||
| rtl_wmbus -f >> "$OUT" 2>/dev/null || true
|
||||
iq_seconds=$((iq_seconds + this))
|
||||
else
|
||||
timeout $((this + 20)) rtl_sdr -f 868950000 -s "$RATE" -g "$GAIN" \
|
||||
-n $((this * RATE)) - 2>>"$ERR" \
|
||||
| rtl_wmbus -f >> "$OUT" 2>/dev/null || true
|
||||
fi
|
||||
t1=$(date +%s)
|
||||
usable=$(( usable + t1 - t0 ))
|
||||
|
||||
# tuner commonly dies during a segment; reset before the next one
|
||||
if grep -q "i2c wr failed" "$ERR"; then
|
||||
echo "--- tuner fault seen; usbreset" >> "$ERR"
|
||||
usbreset 0bda:2838 >> "$ERR" 2>&1 || true
|
||||
recovered=$((recovered + 1))
|
||||
: > "$ERR.tmp"; tail -c 20000 "$ERR" > "$ERR.tmp"; mv "$ERR.tmp" "$ERR"
|
||||
sleep 5
|
||||
fi
|
||||
echo "--- SDR unhealthy; usbreset (try $i)" >> "$ERR"
|
||||
usbreset 0bda:2838 >> "$ERR" 2>&1 || true
|
||||
sleep $((i * 5))
|
||||
done
|
||||
echo "sdr_health_ok=$health_ok" > "${OUT%.log}.health"
|
||||
|
||||
t0=$(date +%s)
|
||||
# tee duplicates the sample stream: one copy to disk, one to the decoder
|
||||
timeout "$DUR" rtl_sdr -f 868950000 -s 1600000 -g "$GAIN" - 2>>"$ERR" \
|
||||
| tee "$IQ" \
|
||||
| rtl_wmbus -f >> "$OUT" 2>/dev/null || true
|
||||
t1=$(date +%s)
|
||||
|
||||
printf 'streamed_seconds=%s\nrequested_seconds=%s\ngain=%s\niq_bytes=%s\n' \
|
||||
"$((t1 - t0))" "$DUR" "$GAIN" "$(stat -c%s "$IQ" 2>/dev/null || echo 0)" \
|
||||
> "$STATS"
|
||||
echo "--- streamed $((t1 - t0))s of ${DUR}s" >> "$ERR"
|
||||
printf 'usable_seconds=%s\nrequested_seconds=%s\nsegments=%s\nrecoveries=%s\ngain=%s\niq_seconds=%s\niq_bytes=%s\n' \
|
||||
"$usable" "$DUR" "$segments" "$recovered" "$GAIN" "$iq_seconds" \
|
||||
"$(stat -c%s "$IQ" 2>/dev/null || echo 0)" > "$STATS"
|
||||
echo "--- usable ${usable}s of ${DUR}s in $segments segment(s), $recovered recovery(ies)" >> "$ERR"
|
||||
|
||||
Reference in New Issue
Block a user