HIL harness, docs, SDR PLL-wedge workaround; firmware flashed and in RX
This commit is contained in:
@@ -0,0 +1,58 @@
|
||||
# RF Configuration — Wireless M-Bus C1 (mode C, meter-to-other)
|
||||
|
||||
## PHY parameters (EN 13757-4, cross-checked against rtl-wmbus source)
|
||||
|
||||
```
|
||||
Frequency: 868.95 MHz
|
||||
Chip/bit rate: 100 kbps NRZ (mode C is NOT 3-of-6 coded, unlike T)
|
||||
Deviation: +/-45 kHz nominal
|
||||
Preamble: alternating 01 chips
|
||||
Sync: 0x543D (shared T/C access code)
|
||||
Mode bytes: 0x54CD -> frame format A, 0x543D -> frame format B
|
||||
```
|
||||
|
||||
Authority used:
|
||||
- rtl-wmbus source (`t1_c1_packet_decoder.h`): `ACCESS_CODE_T1_C1 0x543d`,
|
||||
`C1_MODE_A 0b010101001100`, `C1_MODE_B 0b010101000011`, trailer `0b1101`
|
||||
— concatenated this yields sync sequences 0x543D54CD (A) / 0x543D543D (B).
|
||||
- Frame lengths (over-the-air, incl. L and CRCs):
|
||||
- format A: `1 + L + 2*((L-10+15)/16 + 1)`
|
||||
- format B: `1 + L`
|
||||
|
||||
## SX1262 register-level configuration (firmware/main/sx126x.c)
|
||||
|
||||
```
|
||||
Packet type: GFSK
|
||||
Bitrate: raw 0x002800 (32*32e6/100e3 = 10240 -> 100 kbps)
|
||||
Deviation: raw 0x00B852 (45e3*2^25/32e6 = 47186)
|
||||
Shaping: none (plain 2-FSK; may experiment with BT=0.5)
|
||||
RX bandwidth: 234.3 kHz DSB (code 0x0A) -- signal occupies ~190 kHz
|
||||
Sync word: 0x543D, 16 bits; mode bytes handled as payload so RX and
|
||||
TX share one configuration
|
||||
Preamble TX: 48 bits
|
||||
Preamble det: 8 bits
|
||||
Length mode: fixed, 255-byte capture, truncated in software using the
|
||||
L-field formulas above (SX1262 variable-length mode cannot
|
||||
express wM-Bus length semantics)
|
||||
CRC: radio CRC off; EN 13757 CRC-16 (poly 0x3D65, complemented)
|
||||
validated per block in software
|
||||
Whitening: off
|
||||
RX gain: boosted (reg 0x08AC = 0x96)
|
||||
TX params: default -9 dBm configured (min), ramp 40 us; PA config
|
||||
(0x02,0x02,0x00,0x01) = +14 dBm-optimal table, deliberately
|
||||
capped -- the external KCT8103L PA adds gain on top
|
||||
```
|
||||
|
||||
## Consequences of the fixed-255-byte RX capture
|
||||
|
||||
RxDone fires ~ (255 - frame_len) * 80 us after the actual end of frame;
|
||||
the firmware reconstructs the true end-of-frame timestamp. During that
|
||||
tail the receiver cannot re-arm sync search, adding up to ~20 ms of dead
|
||||
time per frame. Acceptable for the experiment; optimization candidate
|
||||
(GetRxBufferStatus polling with early stop).
|
||||
|
||||
## TX power
|
||||
|
||||
Configured SX1262 power is NOT radiated power: the KCT8103L PA follows.
|
||||
Development default is the SX1262 minimum (-9 dBm). Log lines carry
|
||||
`configured_tx_dbm` to keep this distinction explicit.
|
||||
Reference in New Issue
Block a user