Add repeater protocol and device firmware features
This commit is contained in:
@@ -9,6 +9,7 @@ typedef struct {
|
||||
uint32_t rx_crc_fail;
|
||||
uint32_t rx_not_c1; // sync matched but not C-mode (e.g. T1)
|
||||
uint32_t rx_len_invalid;
|
||||
uint32_t rx_t1; // receptions classified as T-mode (any CRC state)
|
||||
uint32_t rx_bytes;
|
||||
uint32_t tx_attempts;
|
||||
uint32_t tx_success;
|
||||
@@ -24,24 +25,55 @@ typedef struct {
|
||||
} repeater_stats_t;
|
||||
|
||||
typedef struct {
|
||||
uint32_t repeat_delay_ms; // 20..200
|
||||
uint32_t duty_budget_ppm; // rolling-hour TX airtime cap, 0 = disabled
|
||||
uint32_t repeat_delay_ms; // 20..1000; persisted (cfg_store)
|
||||
uint32_t duty_budget_ppm; // rolling-hour TX airtime cap, 0 = disabled; persisted
|
||||
uint32_t beacon_period_ms; // periodic synthetic test frame, 0 = off
|
||||
int8_t tx_power_dbm; // configured SX1262 level, not radiated power
|
||||
bool repeat_enabled;
|
||||
bool verbose;
|
||||
uint32_t whitelist[8]; // A-field ID (4 bytes LE as uint32), 0 = empty slot
|
||||
bool fem_rx_csd; // experimental FEM CSD level in RX
|
||||
uint8_t preamble_bits; // 0, 8, 16, 24 or 32 detected bits
|
||||
uint8_t test_lfield; // 19..200, synthetic frame payload length
|
||||
uint32_t whitelist[8]; // A-field ID (4 bytes LE as uint32)
|
||||
int whitelist_len;
|
||||
} repeater_cfg_t;
|
||||
|
||||
// Radio-owned applied configuration after boot; other tasks may display it,
|
||||
// but all mutations must go through settings_update.
|
||||
extern repeater_cfg_t g_cfg;
|
||||
extern repeater_stats_t g_stats;
|
||||
|
||||
// Last-event snapshot published by the radio task for the local UI.
|
||||
// Written only from the radio task; read from the UI task without locks.
|
||||
// Races tear at most one displayed frame and are deliberately accepted --
|
||||
// the UI must never block or query the radio (docs/FUTURE_UI.md).
|
||||
typedef struct {
|
||||
int64_t rx_ts_us; // 0 = no reception yet
|
||||
uint32_t rx_meter_id; // A-field ID, LE uint32 (prints as meter number)
|
||||
uint32_t rx_hash;
|
||||
int16_t rx_len;
|
||||
int8_t rx_rssi_dbm;
|
||||
char rx_format; // 'A' / 'B'
|
||||
bool rx_crc_ok;
|
||||
int64_t tx_ts_us; // 0 = no TX yet
|
||||
char tx_result[16]; // includes full "radio_timeout" + terminator
|
||||
int64_t hb_ts_us; // last heartbeat probe
|
||||
uint8_t chip_mode;
|
||||
bool config_intact;
|
||||
int8_t rssi_dbm;
|
||||
} repeater_ui_t;
|
||||
|
||||
extern repeater_ui_t g_ui;
|
||||
|
||||
// Rolling-hour duty usage right now. Pure memory reads (ledger + monotonic
|
||||
// clock); safe to call from the UI task.
|
||||
uint64_t repeater_duty_used_us(void);
|
||||
|
||||
void repeater_start(void);
|
||||
void repeater_request_radio_reset(void);
|
||||
void repeater_request_test_tx(void);
|
||||
void repeater_request_test_tx_t1(void);
|
||||
void repeater_request_probe(void);
|
||||
void repeater_set_test_lfield(uint8_t l);
|
||||
void repeater_request_test_burst(void);
|
||||
void repeater_inject_fault(int what); // 1 = standby, 2 = sleep
|
||||
void repeater_print_status(void);
|
||||
|
||||
Reference in New Issue
Block a user