firmware: config-integrity check, fault injection, verified recovery ladder; soak harness
This commit is contained in:
@@ -34,6 +34,7 @@ static volatile bool s_want_radio_reset;
|
||||
static volatile bool s_want_test_tx;
|
||||
static volatile bool s_want_probe;
|
||||
static volatile bool s_want_test_burst;
|
||||
static volatile int s_inject; // 1 = standby, 2 = sleep (config loss)
|
||||
static uint8_t s_test_access_nr;
|
||||
static uint8_t s_test_lfield = 19;
|
||||
static uint32_t s_seq;
|
||||
@@ -95,20 +96,29 @@ static bool recover(const char *reason, int level)
|
||||
bool ok = false;
|
||||
switch (level) {
|
||||
case 1:
|
||||
// Cheapest step: clear IRQ state and re-arm RX. It must only report
|
||||
// success if the radio really is configured and receiving, otherwise
|
||||
// the ladder would stop at a deaf radio.
|
||||
sx126x_clear_irq(SX126X_IRQ_ALL);
|
||||
sx126x_standby();
|
||||
sx126x_restore_rx_payload_len();
|
||||
ok = sx126x_set_rx();
|
||||
ok = sx126x_set_rx() && sx126x_config_intact();
|
||||
if (ok) {
|
||||
vTaskDelay(pdMS_TO_TICKS(2));
|
||||
ok = (((sx126x_get_status() >> 4) & 0x7) == 0x5);
|
||||
}
|
||||
break;
|
||||
case 2:
|
||||
g_stats.radio_reinit++;
|
||||
ok = radio_full_init() && sx126x_set_rx();
|
||||
ok = radio_full_init() && sx126x_set_rx() && sx126x_config_intact();
|
||||
break;
|
||||
case 3:
|
||||
g_stats.fem_reinit++;
|
||||
fem_power(false);
|
||||
vTaskDelay(pdMS_TO_TICKS(20));
|
||||
ok = radio_full_init() && sx126x_set_rx();
|
||||
fem_power(true);
|
||||
vTaskDelay(pdMS_TO_TICKS(5));
|
||||
ok = radio_full_init() && sx126x_set_rx() && sx126x_config_intact();
|
||||
break;
|
||||
default:
|
||||
LOGJ("\"event\":\"radio_recovery\",\"reason\":\"%s\",\"level\":%d,"
|
||||
@@ -496,6 +506,19 @@ static void repeater_task(void *arg)
|
||||
s_want_probe = false;
|
||||
run_probe();
|
||||
}
|
||||
if (s_inject) {
|
||||
int what = s_inject;
|
||||
s_inject = 0;
|
||||
// Deliberately break the radio to exercise detection + the
|
||||
// recovery ladder. The heartbeat probe is expected to notice.
|
||||
if (what == 1) {
|
||||
sx126x_standby();
|
||||
} else {
|
||||
sx126x_inject_sleep();
|
||||
}
|
||||
LOGJ("\"event\":\"fault_injected\",\"fault\":\"%s\"",
|
||||
what == 1 ? "standby" : "sleep");
|
||||
}
|
||||
|
||||
if (ulTaskNotifyTake(pdTRUE, pdMS_TO_TICKS(1000)) > 0) {
|
||||
uint16_t irq = sx126x_get_irq();
|
||||
@@ -511,13 +534,21 @@ static void repeater_task(void *arg)
|
||||
int64_t now = esp_timer_get_time();
|
||||
if (now - last_heartbeat > 10000000LL) {
|
||||
last_heartbeat = now;
|
||||
// consistency probe: chip should be in RX (0x5)
|
||||
// Consistency probe: the chip must be in RX (0x5) AND still
|
||||
// hold its wM-Bus configuration. Checking the mode alone is not
|
||||
// enough: a radio that lost its configuration (reset, sleep,
|
||||
// glitch) can sit in RX looking healthy while deaf to C1.
|
||||
uint8_t st = sx126x_get_status();
|
||||
uint8_t mode = (st >> 4) & 0x7;
|
||||
bool cfg_ok = sx126x_config_intact();
|
||||
LOGJ("\"event\":\"heartbeat\",\"uptime_us\":%lld,\"chip_mode\":%u,"
|
||||
"\"rssi_dbm\":%d", (long long)now, mode, sx126x_get_rssi_inst());
|
||||
"\"config_intact\":%s,\"rssi_dbm\":%d",
|
||||
(long long)now, mode, cfg_ok ? "true" : "false",
|
||||
sx126x_get_rssi_inst());
|
||||
if (mode != 0x5) {
|
||||
recover_ladder("not_in_rx");
|
||||
} else if (!cfg_ok) {
|
||||
recover_ladder("config_lost");
|
||||
}
|
||||
}
|
||||
}
|
||||
@@ -533,6 +564,7 @@ void repeater_request_test_tx(void) { s_want_test_tx = true; }
|
||||
void repeater_request_probe(void) { s_want_probe = true; }
|
||||
void repeater_set_test_lfield(uint8_t l) { s_test_lfield = l; }
|
||||
void repeater_request_test_burst(void) { s_want_test_burst = true; }
|
||||
void repeater_inject_fault(int what) { s_inject = what; }
|
||||
|
||||
// ------------------------------------------------------------------ status
|
||||
|
||||
|
||||
Reference in New Issue
Block a user