From ee76269d31d16c88528c0eba5c6daf811c9dd9ed Mon Sep 17 00:00:00 2001 From: Lars Nolden Date: Tue, 1 Sep 2026 17:00:07 +0200 Subject: [PATCH] findings: withdraw supply-sag conviction; field test record - standalone repeats confirmed, geometry dominates --- docs/FIELD_TEST_2026-09-01.md | 87 +++++++++++++++++++++++++++++++++++ docs/FINDINGS.md | 42 +++++++++++------ 2 files changed, 114 insertions(+), 15 deletions(-) create mode 100644 docs/FIELD_TEST_2026-09-01.md diff --git a/docs/FIELD_TEST_2026-09-01.md b/docs/FIELD_TEST_2026-09-01.md new file mode 100644 index 0000000..c618510 --- /dev/null +++ b/docs/FIELD_TEST_2026-09-01.md @@ -0,0 +1,87 @@ +# Field test — first onsite standalone deployment (2026-09-01, afternoon) + +Setting: the repeater and the HIL laptop (with the Nooelec SDR) moved from +the development bench to a real site. Goal: run the repeater standalone +(no USB host) and verify it over RF alone. This log records what happened, +because the sequence of wrong theories is itself a finding. + +## Timeline of evidence + +| Setup | LED (TxDone) | RF at SDR | Verdict at the time | +|---|---|---|---| +| Laptop USB, board on table (~16:07) | double-blinks | **7/7 TX clock-aligned, median +37 dB over floor** | baseline: transmits | +| Power bank (USB-C, then USB-A) | went dark after seconds | none | bank auto-off at ~60 mA idle load | +| UGREEN 100 W GaN wall charger, C-to-C | double-blinks "sometimes" | none in 4 captures (~8 min) | *wrongly* blamed supply sag | +| LiPo pack attached | blinks, 2-4 double-pulses/90 s | none | supply theory started cracking | +| LiPo + dangling USB cable (no host) | ~9 double-pulses/90 s | none | RX rate recovered; TX still invisible | +| Mid-capture unplug (laptop -> LiPo, position frozen) | blinks throughout | **none in either phase** | laptop connection alone does NOT explain it: power theories all dead | +| Wall power, board hanging free, no LiPo | blinks | none at prior SDR-antenna position | placement of the DUT alone is not it either | +| **SDR antenna moved to ~20 cm from the hanging board** | blinks | **same-duration burst pairs at 50-54 ms: 10-10, 17-17, 16-16 ms** | repeater IS repeating standalone; radiated/received level is simply far lower than the laptop-connected reference | + +## What was actually established + +1. **The repeater works standalone.** On wall power, hanging free, its + RX->50 ms->TX cycle runs (LED) and its repeats are observable at RF + (same-duration pairs at the configured delay) once the observer antenna + is close enough. +2. **The laptop-connected "+37 dB at 50 cm" reference was not a pure + radiated-field measurement.** With the board on the host's USB, the + cable shield and shared ground with the SDR dongle add counterpoise + and possibly conducted common-mode coupling. Standalone, at a similar + claimed distance, the same transmitter was invisible; at ~20 cm it shows + up at +14..+24 dB. The gap between those numbers is the combined effect + of geometry, orientation, antenna environment and the lost cable/ground + contribution -- not a firmware or supply fault. +3. **Every power-source theory failed when tested properly.** + - Power bank: real failure, but trivial (auto-off). The LED found it + in one glance. + - Wall-adapter "sag during PA burst": WITHDRAWN. The adapter is a + 100 W GaN unit, and the frozen-position unplug test showed the + laptop connection failing at the same spot too. The earlier + conviction (committed to FINDINGS.md at the time) was wrong. + - LiPo (stiffest possible rail): same invisibility -> supply exonerated + entirely. +4. **TxDone still proves nothing about radiated power.** The task spec's + warning (§36: "TX successful is not evidence") extends beyond FEM + configuration to antenna geometry: the SX1262 completes its packet into + a mismatched/shadowed antenna exactly as happily as into a good one. + The LED inherits this limit: double-blink = chip-level TX, not RF. +5. **The observer's antenna position is as much a variable as the DUT's.** + Half of today's captures compared "device moved" against "SDR antenna + wherever it happened to be". The decisive experiments were the ones + that froze one side: mid-capture unplug (DUT frozen) and antenna-close + (DUT untouched, observer moved). +6. **Neighbour-meter fingerprint** (for future correlation at this site): + 23-24 ms bursts in trains at ~28-32 ms spacing, plus 10-17 ms singles up + to +42 dB that rail the dongle and produce no rtl-wmbus output. Their + rate is invariant across our firmware versions, reboots and power + sources -- definitively not the repeater. + +## Field lessons for the Solenos gateway + +- **A conducted RF test port would have ended this in minutes.** Half a day + of over-the-air inference replaced one attenuated SMA measurement. + Already in devboard_signals.csv; priority upgraded. +- **Antenna system design is not optional polish.** The stock whip against + a tiny PCB ground radiates so poorly, and so directionally, that + deployment placement dominates link budget. The gateway needs a real + antenna with a defined counterpoise, and the battery pack must be kept + mechanically away from the radiator. +- **On-device persistent telemetry (NVS counters, VBAT) is still the + missing piece.** The LED collapsed "is it powered/alive/repeating" from + four SDR captures to one glance, but every RF question still required + the laptop. Retained counters would have separated "not receiving" from + "not transmitting" instantly. +- **LED patterns earned their place** and should carry to the gateway + (with the FUTURE_UI.md caveat: an LED can only report chip state, never + radiated RF). + +## Still open after this session + +- Clock-aligned close-antenna run (device on laptop serial + SDR antenna + at 20 cm) to attribute bursts per TX event and put a number on the + standalone radiated level. Protocol ready; not yet executed. +- Quantify laptop-cable contribution: repeat the alignment run twice at + identical geometry, cable in vs out (LiPo), antenna close. +- Proper antenna A/B (e.g. quarter-wave with radials vs stock whip) -- + directly relevant to the gateway RF architecture. diff --git a/docs/FINDINGS.md b/docs/FINDINGS.md index 28ccb9a..7b78abb 100644 --- a/docs/FINDINGS.md +++ b/docs/FINDINGS.md @@ -147,19 +147,31 @@ - Long-run stability at >=100 and >=500 verified repeat events. - Early-stop RX (poll GetRxBufferStatus) to cut the ~20 ms deaf tail. -## CONFIRMED (power supply, field debugging 2026-09-01) +## Field test 2026-09-01 (onsite standalone deployment) -- A weak USB supply silently kills radiated TX while everything else looks - healthy: SX1262 reaches TxDone, firmware counts success, LED double-blinks - -- but the SDR 50 cm away sees nothing. A/B proof: laptop USB 7/7 TX - events RF-aligned (median +37 dB over floor); wall adapter minutes later, - same position: 0 of ~expected 5-7 across 80 s (and 0 across four earlier - captures). Suspected mechanism: rail sag during the KCT8103L PA burst. - "TX done" is chip-level packet completion, not radiated power. -- Practical rule: power the repeater from a supply that holds 5 V through - ~400 mA bursts (laptop port, 2 A charger, power-bank USB-A, or LiPo). - After any supply change, verify with one 60 s SDR capture -- the LED - cannot distinguish radiating from non-radiating TX. -- The recurring 10-24 ms bursts at +30..+43 dB ("monster singletons") are a - neighbouring meter railing the dongle, NOT the repeater: their rate is - unchanged across our firmware versions, reboots, and power sources. +Full narrative with the evidence table: docs/FIELD_TEST_2026-09-01.md. + +- WITHDRAWN: an earlier entry here blamed "a weak USB supply" (wall-adapter + rail sag) for killing radiated TX. Disproven the same afternoon: the + adapter is a 100 W GaN unit, a LiPo (stiffest possible rail) showed the + same invisibility, and a frozen-position mid-capture unplug test failed + on laptop power too. The supply was never the cause (except the power + bank's genuine low-load auto-off, which the LED catches at a glance). +- CONFIRMED: the repeater repeats standalone. With the SDR antenna moved to + ~20 cm of the free-hanging, wall-powered board, same-duration burst pairs + appeared at the 50 ms repeat delay (10-10, 17-17, 16-16 ms; received + +14..+24 dB over floor). +- CONFIRMED: the laptop-connected "+37 dB at ~50 cm" reference overstates + standalone radiated field -- the USB cable/host ground contributes + counterpoise (and possibly conducted coupling into the shared-ground + dongle). Radiated performance is dominated by antenna geometry: + orientation, surroundings, and the LiPo pack's position relative to the + antenna. Placement, not power, ruled the day. +- CONFIRMED: TxDone (and therefore the LED double-blink) proves chip-level + packet completion only. It is indistinguishable between a well-matched + antenna and a shadowed/mismatched one -- §36's lesson extended to + antenna geometry. +- CONFIRMED: the recurring 10-24 ms bursts at +30..+43 dB ("monster + singletons", 23-24 ms trains at ~30 ms spacing) are a neighbouring meter + railing the dongle: rate invariant across firmware versions, reboots and + power sources. Excluded from pair detection by fingerprint.