#!/usr/bin/env bash # Full HIL loop for the Heltec V4.3 wM-Bus C1 repeater. # # discover devices -> verify SDR actually receives -> build+flash # -> phase A: TX decodability proof (synthetic C1 bursts) # -> phase B: real-meter RX/repeat correlation # -> phase C: decode-independent IQ repeat proof # -> report (text + JSON), nonzero exit on FAIL # # Usage: ./hil/run.sh [--duration N] [--no-flash] [--tx-power N] [--delay MS] # [--iq-seconds N] [--proof-gain G] # [--gain G] [--min-repeats N] [--no-proof] set -euo pipefail cd "$(dirname "$0")/.." DURATION=300 FLASH=1 TXPOW=-9 DELAY=200 GAIN=42.1 MIN_REPEATS=1 IQ_SECONDS=120 PROOF_GAIN="" PROOF=1 while [ $# -gt 0 ]; do case "$1" in --duration) DURATION=$2; shift 2 ;; --no-flash) FLASH=0; shift ;; --no-proof) PROOF=0; shift ;; --tx-power) TXPOW=$2; shift 2 ;; --delay) DELAY=$2; shift 2 ;; --gain) GAIN=$2; shift 2 ;; --min-repeats) MIN_REPEATS=$2; shift 2 ;; --iq-seconds) IQ_SECONDS=$2; shift 2 ;; --proof-gain) PROOF_GAIN=$2; shift 2 ;; *) echo "unknown arg: $1" >&2; exit 2 ;; esac done PY=./result-py/bin/python3 [ -x "$PY" ] || { echo "run 'nix build .#hil-python -o result-py' first" >&2; exit 2; } # --- 1/2. discover devices (abort on ambiguity) ----------------------------- eval "$(./tools/discover_devices.sh)" echo "DUT: $DUT_PORT" echo "SDR: Nooelec NESDR SMArt v5, index $SDR_INDEX, serial $SDR_SERIAL" RUN_DIR="captures/$(date +%Y-%m-%dT%H-%M-%S)-hil" mkdir -p "$RUN_DIR" echo "run dir: $RUN_DIR" # --- 3. SDR must demonstrably receive before any capture is trusted -------- for i in 1 2 3; do if $PY hil/sdr_health.py > "$RUN_DIR/sdr_health.txt" 2>&1; then break; fi echo "SDR unhealthy (try $i) - resetting" >&2 usbreset 0bda:2838 >/dev/null 2>&1 || true sleep $((i * 5)) done cat "$RUN_DIR/sdr_health.txt" grep -q "SDR_HEALTH=ok" "$RUN_DIR/sdr_health.txt" || { echo "ABORT: SDR observer is deaf; captures would be unattributable" >&2 exit 3 } # --- 4-6. build + flash + reset -------------------------------------------- if [ "$FLASH" = 1 ]; then (cd firmware && idf.py build) > "$RUN_DIR/build.log" 2>&1 if ! (cd firmware && idf.py -p "$DUT_PORT" flash) >> "$RUN_DIR/build.log" 2>&1; then # the port re-enumerates when entering download mode; rediscover once sleep 2 eval "$(./tools/discover_devices.sh)" (cd firmware && idf.py -p "$DUT_PORT" flash) >> "$RUN_DIR/build.log" 2>&1 fi sleep 2 eval "$(./tools/discover_devices.sh)" fi # --- configure DUT -------------------------------------------------------- $PY hil/dut_cmd.py "$DUT_PORT" --listen 3 \ "set repeat_delay_ms $DELAY" "set tx_power $TXPOW" "clear_stats" \ > "$RUN_DIR/setup.log" 2>&1 # --- phase A: TX decodability proof --------------------------------------- # Synthetic C1 frames, each aired twice at the repeat delay. Independent of # meter traffic, and (unlike real repeats) not preceded by a weak frame, # so it isolates "can the SDR decode our C1 TX" from bench dynamic range. if [ "$PROOF" = 1 ]; then echo "phase A: TX decodability proof" ./hil/capture_sdr.sh 70 "$RUN_DIR/proof_sdr.log" "${PROOF_GAIN:-$GAIN}" & SDR_PID=$! sleep 10 for L in 19 60 98; do $PY hil/dut_cmd.py "$DUT_PORT" --listen 8 \ "set test_lfield $L" test_burst >> "$RUN_DIR/proof_serial.log" 2>&1 done wait "$SDR_PID" || true $PY hil/verify_tx.py --serial "$RUN_DIR/proof_serial.log" \ --sdr "$RUN_DIR/proof_sdr.log" > "$RUN_DIR/tx_proof.txt" 2>&1 || true $PY hil/verify_tx.py --serial "$RUN_DIR/proof_serial.log" \ --sdr "$RUN_DIR/proof_sdr.log" --json > "$RUN_DIR/tx_proof.json" 2>&1 || true cat "$RUN_DIR/tx_proof.txt" fi # --- phase B: real meter traffic, decodes + IQ from ONE stream ------------- # One rtl_sdr stream feeds both rtl_wmbus (meter originals) and a raw IQ # file (our transmissions, measured decode-independently). Separate # captures are not comparable: this dongle's sensitivity drifts ~17 dB # over minutes (docs/FINDINGS.md). echo "phase B: real-meter capture (${DURATION}s, decodes + IQ)" IQ="$RUN_DIR/iq.raw" $PY hil/dut_cmd.py "$DUT_PORT" --listen "$DURATION" status \ > "$RUN_DIR/serial.log" 2>&1 & SERIAL_PID=$! if [ "$IQ_SECONDS" -gt 0 ]; then ./hil/capture_both.sh "$DURATION" "$RUN_DIR/rtlwmbus.log" "$IQ" "$GAIN" & else ./hil/capture_sdr.sh "$DURATION" "$RUN_DIR/rtlwmbus.log" "$GAIN" & fi SDR_PID=$! wait "$SDR_PID" || true wait "$SERIAL_PID" || true $PY hil/dut_cmd.py "$DUT_PORT" --listen 4 stats > "$RUN_DIR/final_stats.log" 2>&1 || true cat "$RUN_DIR/final_stats.log" >> "$RUN_DIR/serial.log" # --- RF-level repeat proof from the same stream's IQ ---------------------- if [ -s "$IQ" ]; then echo "RF-level repeat proof from captured IQ" $PY hil/verify_repeats_iq.py --iq "$IQ" --serial "$RUN_DIR/serial.log" \ --delay-ms "$DELAY" > "$RUN_DIR/iq_proof.txt" 2>&1 || true $PY hil/verify_repeats_iq.py --iq "$IQ" --serial "$RUN_DIR/serial.log" \ --delay-ms "$DELAY" --json > "$RUN_DIR/iq_proof.json" 2>&1 || true cat "$RUN_DIR/iq_proof.txt" # IQ is large: keep it only when the proof failed, for offline inspection if grep -q '"tx_events_with_rf": [1-9]' "$RUN_DIR/iq_proof.json" 2>/dev/null; then rm -f "$IQ" fi fi # --- 13-14. correlate ------------------------------------------------------ $PY hil/correlate.py --serial "$RUN_DIR/serial.log" --sdr "$RUN_DIR/rtlwmbus.log" \ --min-delay 0.010 --max-delay 0.400 > "$RUN_DIR/report.json" # --- 15. lockup / reset detection ----------------------------------------- HB=$(grep -c '"event":"heartbeat"' "$RUN_DIR/serial.log" || true) # heartbeats are emitted at >= 10 s cadence (the radio task also does RX/TX # work between them), so allow slack; this catches real stalls, not drift. EXPECTED_HB=$((DURATION / 14)) if [ "$HB" -lt "$EXPECTED_HB" ]; then echo "WARNING: only $HB heartbeats (expected >= $EXPECTED_HB) - possible lockup" \ | tee "$RUN_DIR/lockup_warning.txt" fi # --- 16-18. report --------------------------------------------------------- STREAMED=$(sed -n 's/^usable_seconds=//p' "$RUN_DIR/rtlwmbus.stats" 2>/dev/null || sed -n 's/^streamed_seconds=//p' "$RUN_DIR/rtlwmbus.stats" 2>/dev/null || echo "?") SENS=$(sed -n 's/^SDR_SENSITIVITY=//p' "$RUN_DIR/sdr_health.txt" 2>/dev/null || echo unknown) $PY hil/report.py "$RUN_DIR/report.json" \ --min-repeats "$MIN_REPEATS" --duration "$DURATION" \ --tx-power "$TXPOW" --repeat-delay "$DELAY" \ --sdr-streamed "$STREAMED" \ --sdr-sensitivity "${SENS:-unknown}" \ --tx-proof "$RUN_DIR/tx_proof.json" \ --iq-proof "$RUN_DIR/iq_proof.json" \ | tee "$RUN_DIR/report.txt" RC=${PIPESTATUS[0]} echo "artifacts: $RUN_DIR" exit "$RC"