# Wireless M-Bus C1 Repeater — Heltec WiFi LoRa 32 V4.3 (RF feasibility experiment) Experimental firmware and hardware-in-the-loop test rig answering one question: **can the SX1262 + KCT8103L front-end on the Heltec V4.3 serve as the basis for a Wireless M-Bus gateway/repeater?** Short answer: yes for RX and TX at the PHY level. It receives real C1 meter telegrams, retransmits them bit-exact after a configurable delay, and returns to RX reliably. Quantitative limits and caveats are below. This is **not** a standards-compliant repeater. See [docs/STANDARDS_GAPS.md](docs/STANDARDS_GAPS.md). ## What is here ``` firmware/ ESP-IDF app: SX1262 GFSK driver, wM-Bus C1 RX/TX, repeater state machine, recovery ladder, JSON telemetry firmware/test/ host-side frame-layer tests (run under AddressSanitizer) hil/ hardware-in-the-loop harness (run.sh is the entry point) tools/ device discovery, flashing, reset docs/ hardware evidence, RF config, findings, timing, gaps captures/ per-run artifacts (logs, reports, IQ) flake.nix ESP-IDF + rtl-sdr + rtl-wmbus + wmbusmeters + python env ``` ## Quick start ```bash nix build .#hil-python -o result-py # once nix develop --command ./hil/run.sh --duration 1200 ``` Exit code 0 = PASS. Artifacts land in `captures/-hil/` (`report.txt`, `report.json`, `serial.log`, `rtlwmbus.log`, `iq_proof.txt`). Serial console (scriptable, JSON output): ```bash ./result-py/bin/python3 hil/dut_cmd.py --listen 5 status stats # full command list: docs/TESTING.md ``` ## Results (measured, not inferred) Representative 1200 s run, `captures/2026-09-01T10-34-24-hil`: | Metric | Value | |---|---| | Heltec RX candidates / CRC-valid | 214 / 72 | | SDR-classified originals | 129 (44 meters) | | Heltec matched SDR originals | 47 (36.4 %) | | Heltec TX attempts / success | 72 / 72 (100 %) | | TX events RF-confirmed in IQ | 5 / 5 in the IQ window (100 %) | | Firmware repeat delay (set 200 ms) | 200.001 ms min/median, 200.008 ms max | | Radio recoveries / MCU resets | 0 / 0 | Key hardware findings: - **Pin mapping and FEM control verified** on real hardware — SX1262 on GPIO8-14, KCT8103L on GPIO7/2/5 with CPS driven by DIO2, TCXO on DIO3 at 1.8 V. [docs/HARDWARE.md](docs/HARDWARE.md) - **The KCT8103L RX path is essential**: disabling it (CSD low) costs ~41 dB and drops visible meters from 18 to 1. No overload penalty from maximum front-end gain at this site. [docs/RF_FRONTEND_TESTS.md](docs/RF_FRONTEND_TESTS.md) - **Repeats are bit-exact**: 63/63 logged TX payloads equalled the received raw frame plus C-mode bytes. - **RX deaf time is ~225.7 ms** per repeat at a 200 ms delay, including a 12.2 ms fixed-capture tail imposed by the SX1262 packet engine. [docs/TIMING.md](docs/TIMING.md) ## Measurement caveats — read before trusting any number The RTL-SDR observer is the weakest instrument in this setup and the harness is built around that: 1. Its sensitivity drifts ~17 dB within minutes of streaming, so captures at "the same gain" minutes apart are not comparable. 2. Its tuner dies mid-stream (`i2c wr failed`) without `rtl_sdr` exiting — a naive long capture silently returns "no traffic". The harness uses bounded segments with reset-and-resume. 3. It can de-enumerate entirely, needing a physical replug. `hil/sdr_health.py` gates every run and every report states the observer state (`full` / `degraded`), so an empty capture is always attributable. An earlier claimed "97 % RX match rate" was withdrawn after it turned out to have been measured against a degraded observer. Our transmission also arrives far stronger than meter traffic (up to ~36 dB at full observer sensitivity), which pushes the dongle into compression so rtl-wmbus receives our repeat with 1-2 byte errors and fails CRC. Repeats are therefore verified two ways that are immune to this: - synthetic C1 bursts prove the framing is decodable as C1 (`verify_tx.py`); - firmware TX timestamps are aligned to bursts in raw IQ to prove real repeats radiate with the right timing and airtime (`verify_repeats_iq.py`). Closing the remaining gap needs physical antenna separation or an inline attenuator, which is not scriptable from the host. ## Documentation - [HARDWARE.md](docs/HARDWARE.md) — board, pin mapping, FEM, observer faults - [RF_CONFIG.md](docs/RF_CONFIG.md) — C1 PHY and SX1262 register settings - [RF_FRONTEND_TESTS.md](docs/RF_FRONTEND_TESTS.md) — RX comparisons, LNA A/B - [TIMING.md](docs/TIMING.md) — latency and deaf-time instrumentation - [SDR_BASELINE.md](docs/SDR_BASELINE.md) — Phase 0 observer baseline - [FINDINGS.md](docs/FINDINGS.md) — confirmed / disproven / needs testing - [OPEN_QUESTIONS.md](docs/OPEN_QUESTIONS.md) — open and closed questions - [STANDARDS_GAPS.md](docs/STANDARDS_GAPS.md) — deviations from EN 13757/OMS - [TESTING.md](docs/TESTING.md) — how to run things, known pitfalls - [DEVBOARD_REQUIREMENTS.md](docs/DEVBOARD_REQUIREMENTS.md) + [devboard_signals.csv](docs/devboard_signals.csv) — future PCB needs