# Field test — first onsite standalone deployment (2026-09-01, afternoon) Setting: the repeater and the HIL laptop (with the Nooelec SDR) moved from the development bench to a real site. Goal: run the repeater standalone (no USB host) and verify it over RF alone. This log records what happened, because the sequence of wrong theories is itself a finding. ## Timeline of evidence | Setup | LED (TxDone) | RF at SDR | Verdict at the time | |---|---|---|---| | Laptop USB, board on table (~16:07) | double-blinks | **7/7 TX clock-aligned, median +37 dB over floor** | baseline: transmits | | Power bank (USB-C, then USB-A) | went dark after seconds | none | bank auto-off at ~60 mA idle load | | UGREEN 100 W GaN wall charger, C-to-C | double-blinks "sometimes" | none in 4 captures (~8 min) | *wrongly* blamed supply sag | | LiPo pack attached | blinks, 2-4 double-pulses/90 s | none | supply theory started cracking | | LiPo + dangling USB cable (no host) | ~9 double-pulses/90 s | none | RX rate recovered; TX still invisible | | Mid-capture unplug (laptop -> LiPo, position frozen) | blinks throughout | **none in either phase** | laptop connection alone does NOT explain it: power theories all dead | | Wall power, board hanging free, no LiPo | blinks | none at prior SDR-antenna position | placement of the DUT alone is not it either | | **SDR antenna moved to ~20 cm from the hanging board** | blinks | **same-duration burst pairs at 50-54 ms: 10-10, 17-17, 16-16 ms** | repeater IS repeating standalone; radiated/received level is simply far lower than the laptop-connected reference | ## What was actually established 1. **The repeater works standalone.** On wall power, hanging free, its RX->50 ms->TX cycle runs (LED) and its repeats are observable at RF (same-duration pairs at the configured delay) once the observer antenna is close enough. 2. **The laptop-connected "+37 dB at 50 cm" reference was not a pure radiated-field measurement.** With the board on the host's USB, the cable shield and shared ground with the SDR dongle add counterpoise and possibly conducted common-mode coupling. Standalone, at a similar claimed distance, the same transmitter was invisible; at ~20 cm it shows up at +14..+24 dB. The gap between those numbers is the combined effect of geometry, orientation, antenna environment and the lost cable/ground contribution -- not a firmware or supply fault. 3. **Every power-source theory failed when tested properly.** - Power bank: real failure, but trivial (auto-off). The LED found it in one glance. - Wall-adapter "sag during PA burst": WITHDRAWN. The adapter is a 100 W GaN unit, and the frozen-position unplug test showed the laptop connection failing at the same spot too. The earlier conviction (committed to FINDINGS.md at the time) was wrong. - LiPo (stiffest possible rail): same invisibility -> supply exonerated entirely. 4. **TxDone still proves nothing about radiated power.** The task spec's warning (§36: "TX successful is not evidence") extends beyond FEM configuration to antenna geometry: the SX1262 completes its packet into a mismatched/shadowed antenna exactly as happily as into a good one. The LED inherits this limit: double-blink = chip-level TX, not RF. 5. **The observer's antenna position is as much a variable as the DUT's.** Half of today's captures compared "device moved" against "SDR antenna wherever it happened to be". The decisive experiments were the ones that froze one side: mid-capture unplug (DUT frozen) and antenna-close (DUT untouched, observer moved). 6. **Neighbour-meter fingerprint** (for future correlation at this site): 23-24 ms bursts in trains at ~28-32 ms spacing, plus 10-17 ms singles up to +42 dB that rail the dongle and produce no rtl-wmbus output. Their rate is invariant across our firmware versions, reboots and power sources -- definitively not the repeater. ## Field lessons for the Solenos gateway - **A conducted RF test port would have ended this in minutes.** Half a day of over-the-air inference replaced one attenuated SMA measurement. Already in devboard_signals.csv; priority upgraded. - **Antenna system design is not optional polish.** The stock whip against a tiny PCB ground radiates so poorly, and so directionally, that deployment placement dominates link budget. The gateway needs a real antenna with a defined counterpoise, and the battery pack must be kept mechanically away from the radiator. - **On-device persistent telemetry (NVS counters, VBAT) is still the missing piece.** The LED collapsed "is it powered/alive/repeating" from four SDR captures to one glance, but every RF question still required the laptop. Retained counters would have separated "not receiving" from "not transmitting" instantly. - **LED patterns earned their place** and should carry to the gateway (with the FUTURE_UI.md caveat: an LED can only report chip state, never radiated RF). ## Still open after this session - Clock-aligned close-antenna run (device on laptop serial + SDR antenna at 20 cm) to attribute bursts per TX event and put a number on the standalone radiated level. Protocol ready; not yet executed. - Quantify laptop-cable contribution: repeat the alignment run twice at identical geometry, cable in vs out (LiPo), antenna close. - Proper antenna A/B (e.g. quarter-wave with radials vs stock whip) -- directly relevant to the gateway RF architecture.