5.2 KiB
Wireless M-Bus C1 Repeater — Heltec WiFi LoRa 32 V4.3 (RF feasibility experiment)
Experimental firmware and hardware-in-the-loop test rig answering one question: can the SX1262 + KCT8103L front-end on the Heltec V4.3 serve as the basis for a Wireless M-Bus gateway/repeater?
Short answer: yes for RX and TX at the PHY level. It receives real C1 meter telegrams, retransmits them bit-exact after a configurable delay, and returns to RX reliably. Quantitative limits and caveats are below.
This is not a standards-compliant repeater. See docs/STANDARDS_GAPS.md.
What is here
firmware/ ESP-IDF app: SX1262 GFSK driver, wM-Bus C1 RX/TX,
repeater state machine, recovery ladder, JSON telemetry
hil/ hardware-in-the-loop harness (run.sh is the entry point)
tools/ device discovery, flashing, reset
docs/ hardware evidence, RF config, findings, timing, gaps
captures/ per-run artifacts (logs, reports, IQ)
flake.nix ESP-IDF + rtl-sdr + rtl-wmbus + wmbusmeters + python env
Quick start
nix build .#hil-python -o result-py # once
nix develop --command ./hil/run.sh --duration 1200
Exit code 0 = PASS. Artifacts land in captures/<timestamp>-hil/
(report.txt, report.json, serial.log, rtlwmbus.log, iq_proof.txt).
Serial console (scriptable, JSON output):
./result-py/bin/python3 hil/dut_cmd.py <port> --listen 5 status stats
# status | stats | clear_stats | radio_status | radio_reset | probe
# test_tx | test_burst | reboot
# set repeat_delay_ms N | set tx_power N | set repeat_enabled 0|1
# set verbose 0|1 | set fem_rx_csd 0|1 | set pa_low 0|1
# set test_lfield N | set whitelist ID[,ID...] | set whitelist clear
Results (measured, not inferred)
Representative 1200 s run, captures/2026-09-01T10-34-24-hil:
| Metric | Value |
|---|---|
| Heltec RX candidates / CRC-valid | 214 / 72 |
| SDR-classified originals | 129 (44 meters) |
| Heltec matched SDR originals | 47 (36.4 %) |
| Heltec TX attempts / success | 72 / 72 (100 %) |
| TX events RF-confirmed in IQ | 5 / 5 in the IQ window (100 %) |
| Firmware repeat delay (set 200 ms) | 200.001 ms min/median, 200.008 ms max |
| Radio recoveries / MCU resets | 0 / 0 |
Key hardware findings:
- Pin mapping and FEM control verified on real hardware — SX1262 on GPIO8-14, KCT8103L on GPIO7/2/5 with CPS driven by DIO2, TCXO on DIO3 at 1.8 V. docs/HARDWARE.md
- The KCT8103L RX path is essential: disabling it (CSD low) costs ~41 dB and drops visible meters from 18 to 1. No overload penalty from maximum front-end gain at this site. docs/RF_FRONTEND_TESTS.md
- Repeats are bit-exact: 63/63 logged TX payloads equalled the received raw frame plus C-mode bytes.
- RX deaf time is ~225.7 ms per repeat at a 200 ms delay, including a 12.2 ms fixed-capture tail imposed by the SX1262 packet engine. docs/TIMING.md
Measurement caveats — read before trusting any number
The RTL-SDR observer is the weakest instrument in this setup and the harness is built around that:
- Its sensitivity drifts ~17 dB within minutes of streaming, so captures at "the same gain" minutes apart are not comparable.
- Its tuner dies mid-stream (
i2c wr failed) withoutrtl_sdrexiting — a naive long capture silently returns "no traffic". The harness uses bounded segments with reset-and-resume. - It can de-enumerate entirely, needing a physical replug.
hil/sdr_health.py gates every run and every report states the observer
state (full / degraded), so an empty capture is always attributable.
An earlier claimed "97 % RX match rate" was withdrawn after it turned out
to have been measured against a degraded observer.
Our transmission also arrives far stronger than meter traffic (up to ~36 dB at full observer sensitivity), which pushes the dongle into compression so rtl-wmbus receives our repeat with 1-2 byte errors and fails CRC. Repeats are therefore verified two ways that are immune to this:
- synthetic C1 bursts prove the framing is decodable as C1 (
verify_tx.py); - firmware TX timestamps are aligned to bursts in raw IQ to prove real
repeats radiate with the right timing and airtime
(
verify_repeats_iq.py).
Closing the remaining gap needs physical antenna separation or an inline attenuator, which is not scriptable from the host.
Documentation
- HARDWARE.md — board, pin mapping, FEM, observer faults
- RF_CONFIG.md — C1 PHY and SX1262 register settings
- RF_FRONTEND_TESTS.md — RX comparisons, LNA A/B
- TIMING.md — latency and deaf-time instrumentation
- SDR_BASELINE.md — Phase 0 observer baseline
- FINDINGS.md — confirmed / disproven / needs testing
- OPEN_QUESTIONS.md — open and closed questions
- STANDARDS_GAPS.md — deviations from EN 13757/OMS
- TESTING.md — how to run things, known pitfalls
- DEVBOARD_REQUIREMENTS.md + devboard_signals.csv — future PCB needs