findings: withdraw supply-sag conviction; field test record - standalone repeats confirmed, geometry dominates
This commit is contained in:
+27
-15
@@ -147,19 +147,31 @@
|
||||
- Long-run stability at >=100 and >=500 verified repeat events.
|
||||
- Early-stop RX (poll GetRxBufferStatus) to cut the ~20 ms deaf tail.
|
||||
|
||||
## CONFIRMED (power supply, field debugging 2026-09-01)
|
||||
## Field test 2026-09-01 (onsite standalone deployment)
|
||||
|
||||
- A weak USB supply silently kills radiated TX while everything else looks
|
||||
healthy: SX1262 reaches TxDone, firmware counts success, LED double-blinks
|
||||
-- but the SDR 50 cm away sees nothing. A/B proof: laptop USB 7/7 TX
|
||||
events RF-aligned (median +37 dB over floor); wall adapter minutes later,
|
||||
same position: 0 of ~expected 5-7 across 80 s (and 0 across four earlier
|
||||
captures). Suspected mechanism: rail sag during the KCT8103L PA burst.
|
||||
"TX done" is chip-level packet completion, not radiated power.
|
||||
- Practical rule: power the repeater from a supply that holds 5 V through
|
||||
~400 mA bursts (laptop port, 2 A charger, power-bank USB-A, or LiPo).
|
||||
After any supply change, verify with one 60 s SDR capture -- the LED
|
||||
cannot distinguish radiating from non-radiating TX.
|
||||
- The recurring 10-24 ms bursts at +30..+43 dB ("monster singletons") are a
|
||||
neighbouring meter railing the dongle, NOT the repeater: their rate is
|
||||
unchanged across our firmware versions, reboots, and power sources.
|
||||
Full narrative with the evidence table: docs/FIELD_TEST_2026-09-01.md.
|
||||
|
||||
- WITHDRAWN: an earlier entry here blamed "a weak USB supply" (wall-adapter
|
||||
rail sag) for killing radiated TX. Disproven the same afternoon: the
|
||||
adapter is a 100 W GaN unit, a LiPo (stiffest possible rail) showed the
|
||||
same invisibility, and a frozen-position mid-capture unplug test failed
|
||||
on laptop power too. The supply was never the cause (except the power
|
||||
bank's genuine low-load auto-off, which the LED catches at a glance).
|
||||
- CONFIRMED: the repeater repeats standalone. With the SDR antenna moved to
|
||||
~20 cm of the free-hanging, wall-powered board, same-duration burst pairs
|
||||
appeared at the 50 ms repeat delay (10-10, 17-17, 16-16 ms; received
|
||||
+14..+24 dB over floor).
|
||||
- CONFIRMED: the laptop-connected "+37 dB at ~50 cm" reference overstates
|
||||
standalone radiated field -- the USB cable/host ground contributes
|
||||
counterpoise (and possibly conducted coupling into the shared-ground
|
||||
dongle). Radiated performance is dominated by antenna geometry:
|
||||
orientation, surroundings, and the LiPo pack's position relative to the
|
||||
antenna. Placement, not power, ruled the day.
|
||||
- CONFIRMED: TxDone (and therefore the LED double-blink) proves chip-level
|
||||
packet completion only. It is indistinguishable between a well-matched
|
||||
antenna and a shadowed/mismatched one -- §36's lesson extended to
|
||||
antenna geometry.
|
||||
- CONFIRMED: the recurring 10-24 ms bursts at +30..+43 dB ("monster
|
||||
singletons", 23-24 ms trains at ~30 ms spacing) are a neighbouring meter
|
||||
railing the dongle: rate invariant across firmware versions, reboots and
|
||||
power sources. Excluded from pair detection by fingerprint.
|
||||
|
||||
Reference in New Issue
Block a user