findings: withdraw supply-sag conviction; field test record - standalone repeats confirmed, geometry dominates

This commit is contained in:
Lars Nolden
2026-09-01 17:00:07 +02:00
parent 6e75eb57fd
commit ee76269d31
2 changed files with 114 additions and 15 deletions
+87
View File
@@ -0,0 +1,87 @@
# Field test — first onsite standalone deployment (2026-09-01, afternoon)
Setting: the repeater and the HIL laptop (with the Nooelec SDR) moved from
the development bench to a real site. Goal: run the repeater standalone
(no USB host) and verify it over RF alone. This log records what happened,
because the sequence of wrong theories is itself a finding.
## Timeline of evidence
| Setup | LED (TxDone) | RF at SDR | Verdict at the time |
|---|---|---|---|
| Laptop USB, board on table (~16:07) | double-blinks | **7/7 TX clock-aligned, median +37 dB over floor** | baseline: transmits |
| Power bank (USB-C, then USB-A) | went dark after seconds | none | bank auto-off at ~60 mA idle load |
| UGREEN 100 W GaN wall charger, C-to-C | double-blinks "sometimes" | none in 4 captures (~8 min) | *wrongly* blamed supply sag |
| LiPo pack attached | blinks, 2-4 double-pulses/90 s | none | supply theory started cracking |
| LiPo + dangling USB cable (no host) | ~9 double-pulses/90 s | none | RX rate recovered; TX still invisible |
| Mid-capture unplug (laptop -> LiPo, position frozen) | blinks throughout | **none in either phase** | laptop connection alone does NOT explain it: power theories all dead |
| Wall power, board hanging free, no LiPo | blinks | none at prior SDR-antenna position | placement of the DUT alone is not it either |
| **SDR antenna moved to ~20 cm from the hanging board** | blinks | **same-duration burst pairs at 50-54 ms: 10-10, 17-17, 16-16 ms** | repeater IS repeating standalone; radiated/received level is simply far lower than the laptop-connected reference |
## What was actually established
1. **The repeater works standalone.** On wall power, hanging free, its
RX->50 ms->TX cycle runs (LED) and its repeats are observable at RF
(same-duration pairs at the configured delay) once the observer antenna
is close enough.
2. **The laptop-connected "+37 dB at 50 cm" reference was not a pure
radiated-field measurement.** With the board on the host's USB, the
cable shield and shared ground with the SDR dongle add counterpoise
and possibly conducted common-mode coupling. Standalone, at a similar
claimed distance, the same transmitter was invisible; at ~20 cm it shows
up at +14..+24 dB. The gap between those numbers is the combined effect
of geometry, orientation, antenna environment and the lost cable/ground
contribution -- not a firmware or supply fault.
3. **Every power-source theory failed when tested properly.**
- Power bank: real failure, but trivial (auto-off). The LED found it
in one glance.
- Wall-adapter "sag during PA burst": WITHDRAWN. The adapter is a
100 W GaN unit, and the frozen-position unplug test showed the
laptop connection failing at the same spot too. The earlier
conviction (committed to FINDINGS.md at the time) was wrong.
- LiPo (stiffest possible rail): same invisibility -> supply exonerated
entirely.
4. **TxDone still proves nothing about radiated power.** The task spec's
warning (§36: "TX successful is not evidence") extends beyond FEM
configuration to antenna geometry: the SX1262 completes its packet into
a mismatched/shadowed antenna exactly as happily as into a good one.
The LED inherits this limit: double-blink = chip-level TX, not RF.
5. **The observer's antenna position is as much a variable as the DUT's.**
Half of today's captures compared "device moved" against "SDR antenna
wherever it happened to be". The decisive experiments were the ones
that froze one side: mid-capture unplug (DUT frozen) and antenna-close
(DUT untouched, observer moved).
6. **Neighbour-meter fingerprint** (for future correlation at this site):
23-24 ms bursts in trains at ~28-32 ms spacing, plus 10-17 ms singles up
to +42 dB that rail the dongle and produce no rtl-wmbus output. Their
rate is invariant across our firmware versions, reboots and power
sources -- definitively not the repeater.
## Field lessons for the Solenos gateway
- **A conducted RF test port would have ended this in minutes.** Half a day
of over-the-air inference replaced one attenuated SMA measurement.
Already in devboard_signals.csv; priority upgraded.
- **Antenna system design is not optional polish.** The stock whip against
a tiny PCB ground radiates so poorly, and so directionally, that
deployment placement dominates link budget. The gateway needs a real
antenna with a defined counterpoise, and the battery pack must be kept
mechanically away from the radiator.
- **On-device persistent telemetry (NVS counters, VBAT) is still the
missing piece.** The LED collapsed "is it powered/alive/repeating" from
four SDR captures to one glance, but every RF question still required
the laptop. Retained counters would have separated "not receiving" from
"not transmitting" instantly.
- **LED patterns earned their place** and should carry to the gateway
(with the FUTURE_UI.md caveat: an LED can only report chip state, never
radiated RF).
## Still open after this session
- Clock-aligned close-antenna run (device on laptop serial + SDR antenna
at 20 cm) to attribute bursts per TX event and put a number on the
standalone radiated level. Protocol ready; not yet executed.
- Quantify laptop-cable contribution: repeat the alignment run twice at
identical geometry, cable in vs out (LiPo), antenna close.
- Proper antenna A/B (e.g. quarter-wave with radials vs stock whip) --
directly relevant to the gateway RF architecture.
+27 -15
View File
@@ -147,19 +147,31 @@
- Long-run stability at >=100 and >=500 verified repeat events. - Long-run stability at >=100 and >=500 verified repeat events.
- Early-stop RX (poll GetRxBufferStatus) to cut the ~20 ms deaf tail. - Early-stop RX (poll GetRxBufferStatus) to cut the ~20 ms deaf tail.
## CONFIRMED (power supply, field debugging 2026-09-01) ## Field test 2026-09-01 (onsite standalone deployment)
- A weak USB supply silently kills radiated TX while everything else looks Full narrative with the evidence table: docs/FIELD_TEST_2026-09-01.md.
healthy: SX1262 reaches TxDone, firmware counts success, LED double-blinks
-- but the SDR 50 cm away sees nothing. A/B proof: laptop USB 7/7 TX - WITHDRAWN: an earlier entry here blamed "a weak USB supply" (wall-adapter
events RF-aligned (median +37 dB over floor); wall adapter minutes later, rail sag) for killing radiated TX. Disproven the same afternoon: the
same position: 0 of ~expected 5-7 across 80 s (and 0 across four earlier adapter is a 100 W GaN unit, a LiPo (stiffest possible rail) showed the
captures). Suspected mechanism: rail sag during the KCT8103L PA burst. same invisibility, and a frozen-position mid-capture unplug test failed
"TX done" is chip-level packet completion, not radiated power. on laptop power too. The supply was never the cause (except the power
- Practical rule: power the repeater from a supply that holds 5 V through bank's genuine low-load auto-off, which the LED catches at a glance).
~400 mA bursts (laptop port, 2 A charger, power-bank USB-A, or LiPo). - CONFIRMED: the repeater repeats standalone. With the SDR antenna moved to
After any supply change, verify with one 60 s SDR capture -- the LED ~20 cm of the free-hanging, wall-powered board, same-duration burst pairs
cannot distinguish radiating from non-radiating TX. appeared at the 50 ms repeat delay (10-10, 17-17, 16-16 ms; received
- The recurring 10-24 ms bursts at +30..+43 dB ("monster singletons") are a +14..+24 dB over floor).
neighbouring meter railing the dongle, NOT the repeater: their rate is - CONFIRMED: the laptop-connected "+37 dB at ~50 cm" reference overstates
unchanged across our firmware versions, reboots, and power sources. standalone radiated field -- the USB cable/host ground contributes
counterpoise (and possibly conducted coupling into the shared-ground
dongle). Radiated performance is dominated by antenna geometry:
orientation, surroundings, and the LiPo pack's position relative to the
antenna. Placement, not power, ruled the day.
- CONFIRMED: TxDone (and therefore the LED double-blink) proves chip-level
packet completion only. It is indistinguishable between a well-matched
antenna and a shadowed/mismatched one -- §36's lesson extended to
antenna geometry.
- CONFIRMED: the recurring 10-24 ms bursts at +30..+43 dB ("monster
singletons", 23-24 ms trains at ~30 ms spacing) are a neighbouring meter
railing the dongle: rate invariant across firmware versions, reboots and
power sources. Excluded from pair detection by fingerprint.