Files

3.9 KiB

RF Configuration — Wireless M-Bus C1 (mode C, meter-to-other)

PHY parameters (EN 13757-4, cross-checked against rtl-wmbus source)

Frequency:      868.95 MHz
Chip/bit rate:  100 kbps NRZ (mode C is NOT 3-of-6 coded, unlike T)
Deviation:      +/-45 kHz nominal
Preamble:       alternating 01 chips
Sync:           0x543D (shared T/C access code)
Mode bytes:     0x54CD -> frame format A, 0x543D -> frame format B

Authority used:

  • rtl-wmbus source (t1_c1_packet_decoder.h): ACCESS_CODE_T1_C1 0x543d, C1_MODE_A 0b010101001100, C1_MODE_B 0b010101000011, trailer 0b1101 — concatenated this yields sync sequences 0x543D54CD (A) / 0x543D543D (B).
  • Frame lengths (over-the-air, incl. L and CRCs):
    • format A: 1 + L + 2*((L-10+15)/16 + 1)
    • format B: 1 + L

SX1262 register-level configuration (firmware/main/sx126x.c)

Packet type:    GFSK
Bitrate:        raw 0x002800  (32*32e6/100e3 = 10240 -> 100 kbps)
Deviation:      raw 0x00B852  (45e3*2^25/32e6 = 47186)
Shaping:        none (plain 2-FSK; may experiment with BT=0.5)
RX bandwidth:   234.3 kHz DSB (code 0x0A) -- signal occupies ~190 kHz
Sync word:      0x543D, 16 bits; mode bytes handled as payload so RX and
                TX share one configuration
Preamble TX:    48 bits
Preamble det:   8 bits
Length mode:    fixed, 255-byte capture, truncated in software using the
                L-field formulas above (SX1262 variable-length mode cannot
                express wM-Bus length semantics)
CRC:            radio CRC off; EN 13757 CRC-16 (poly 0x3D65, complemented)
                validated per block in software
Whitening:      off
RX gain:        boosted (reg 0x08AC = 0x96)
TX params:      default -9 dBm configured (min), ramp 40 us; PA config
                (0x02,0x02,0x00,0x01) = +14 dBm-optimal table, deliberately
                capped -- the external KCT8103L PA adds gain on top

PA-row invariant: deviceSel must remain 0x00 for SX1262, and the other bytes must come from an SX1262 row. The removed diagnostic (0x01,0x00,0x00,0x01) mixed the SX1261 +10 dBm PA-duty/hpMax values with SX1262 selection. This undocumented hybrid reduced measured RF by about 32 dB while all chip-side TX diagnostics still passed.

Consequences of the fixed-255-byte RX capture

RxDone fires ~ (255 - frame_len) * 80 us after the actual end of frame; the firmware reconstructs the true end-of-frame timestamp. During that tail the receiver cannot re-arm sync search, adding up to ~20 ms of dead time per frame. Acceptable for the experiment; optimization candidate (GetRxBufferStatus polling with early stop).

TX power

Configured SX1262 power is NOT radiated power: the KCT8103L PA follows. Development default is the SX1262 minimum (-9 dBm), and the console accepts only -9..+2 dBm. +2 is the level used by known-good Heltec V4.3 firmware, not a declaration of legal radiated power. Keep -9 dBm until the complete FEM/antenna path has a conducted or calibrated e.r.p. measurement.

wmbus_tx.configured_tx_dbm records SetTxParams. airtime_us is computed channel occupancy (48-bit preamble + 16-bit sync + payload at 100 kbps); tx_operation_us is the longer firmware-entry-through-TxDone latency.

T-mode (T1) support

T1 shares the 0x543D access code, so ONE radio configuration receives both modes: C-mode announces itself with two NRZ mode bytes after the sync; T-mode continues directly with 3-of-6 coded data (decoded in software from the same fixed 255-byte capture; wM-Bus C/T share the 100 kchip/s rate). Tables verified against rtl-wmbus.

TX: T1 frames are 3-of-6 encoded in software and sent with 50 kHz FSK deviation (raw 0x00CCCD) instead of C-mode's 45 kHz; the swap is a lazy per-TX SetModulationParams (deviation is a TX-only GFSK parameter, RX is unaffected). Verified: rtl_wmbus decodes our synthetic T1 frames, including L=140.

Length caps from the fixed 255-byte capture: C1 total <= 253 bytes; T1 total <= 170 decoded bytes (coded 1.5x).