1.9 KiB
1.9 KiB
| 1 | signal | device | gpio | direction | voltage | interrupt | timing_critical | test_point_required | header_required | reason |
|---|---|---|---|---|---|---|---|---|---|---|
| 2 | WMBUS_NSS | SX1262 | 8 | output | 3.3 | false | true | true | true | SPI decode of radio commands during bring-up |
| 3 | WMBUS_SCK | SX1262 | 9 | output | 3.3 | false | true | true | true | SPI decode |
| 4 | WMBUS_MOSI | SX1262 | 10 | output | 3.3 | false | true | true | true | SPI decode |
| 5 | WMBUS_MISO | SX1262 | 11 | input | 3.3 | false | true | true | true | SPI decode |
| 6 | WMBUS_RESET | SX1262 | 12 | output | 3.3 | false | false | true | true | radio recovery verification |
| 7 | WMBUS_BUSY | SX1262 | 13 | input | 3.3 | false | true | true | true | command-timing and stuck-BUSY debugging |
| 8 | WMBUS_DIO1 | SX1262 | 14 | input | 3.3 | true | true | true | true | RX/TX IRQ latency measurement |
| 9 | FEM_PWR_EN | KCT8103L | 7 | output | 3.3 | false | false | true | true | FEM power sequencing verification |
| 10 | FEM_CSD | KCT8103L | 2 | output | 3.3 | false | false | true | true | FEM enable + board-revision detection (pull level) |
| 11 | FEM_CTX | KCT8103L | 5 | output | 3.3 | false | true | true | true | RX/TX path switch timing vs TX start |
| 12 | ESP_USB_DN | ESP32-S3 | 19 | bidir | 3.3 | false | false | false | true | flash/console; must stay accessible |
| 13 | ESP_USB_DP | ESP32-S3 | 20 | bidir | 3.3 | false | false | false | true | flash/console |
| 14 | RADIO_VDD_SENSE | SX1262 | analog | 3.3 | false | true | true | false | current sense to confirm PA activity during TX | |
| 15 | LOG_UART_TX | ESP32-S3 | 43 | output | 3.3 | false | false | true | true | always-on boot/log output independent of native USB |
| 16 | RF_TAP | antenna | rf | false | false | true | false | conducted measurement port with fixed attenuator to avoid observer overload | ||
| 17 | OLED_SDA | SSD1306 | 17 | bidir | 3.3 | false | false | true | true | local status UI; must not share a bus with RF-critical peripherals |
| 18 | OLED_SCL | SSD1306 | 18 | output | 3.3 | false | false | true | true | local status UI |
| 19 | OLED_RST | SSD1306 | 21 | output | 3.3 | false | false | true | false | display enable/reset; LOW then HIGH with 50ms settle |
| 20 | VEXT_EN | board | 36 | output | 3.3 | false | false | true | false | active-low external rail powering the display; verify what else it gates |
| 21 | BTN_USR | ESP32-S3 | 0 | input | 3.3 | true | false | true | true | user button; also BOOT strap so unusable for boot-time gestures |