107 lines
4.2 KiB
Markdown
107 lines
4.2 KiB
Markdown
# Hardware
|
|
|
|
## Board
|
|
|
|
```
|
|
Board: Heltec WiFi LoRa 32 V4.3
|
|
Model: HTIT-WB32LAF
|
|
MCU: ESP32-S3 (16 MB flash, 2 MB PSRAM)
|
|
Radio: Semtech SX1262
|
|
FEM: KCT8103L (868-928 MHz high-power variant)
|
|
```
|
|
|
|
DUT USB identity (native ESP32-S3 USB):
|
|
- factory Arduino firmware enumerates as `usb-Espressif_Systems_heltec_wifi_lora_32_v4__16_MB_FLASH__2_MB_PSRAM__F85B1BA1F86C-if00`
|
|
- our ESP-IDF firmware / ROM bootloader enumerate as `usb-Espressif_USB_JTAG_serial_debug_unit_F8:5B:1B:A1:F8:6C-if00`
|
|
|
|
`tools/discover_devices.sh` handles both.
|
|
|
|
## SX1262 pin mapping — DOCUMENTED + EXPERIMENTALLY VERIFIED
|
|
|
|
```
|
|
SX1262:
|
|
NSS GPIO8
|
|
SCK GPIO9
|
|
MOSI GPIO10
|
|
MISO GPIO11
|
|
RESET GPIO12
|
|
BUSY GPIO13
|
|
DIO1 GPIO14
|
|
```
|
|
|
|
Verified: SPI register write/readback passes and GFSK RX runs
|
|
(`radio_init` diagnostic: `spi:true, reset:true, tcxo:true`, heartbeat
|
|
`chip_mode:5` = RX with plausible RSSI). See docs/FINDINGS.md.
|
|
|
|
Sources:
|
|
- Heltec product manual / wiki, "WiFi LoRa 32 V4":
|
|
https://wiki.heltec.org/docs/devices/open-source-hardware/esp32-series/lora-32/wifi-lora-32-v4/
|
|
- Heltec schematic: https://resource.heltec.cn/download/WiFi_LoRa_32_V4/Schematic/HTIT-WB32LAF_V4.3.pdf
|
|
- RNode_Firmware 1.86 board table via jrl290/RTNode-HeltecV4 `Boards.h`
|
|
(working firmware for this exact board):
|
|
https://github.com/jrl290/RTNode-HeltecV4
|
|
|
|
## KCT8103L FEM — DOCUMENTED + EXPERIMENTALLY VERIFIED
|
|
|
|
```
|
|
FEM:
|
|
POWER GPIO7 supply enable, drive HIGH
|
|
CSD GPIO2 chip enable, drive HIGH (internal pull-up on KCT8103L)
|
|
CTX GPIO5 path select: LOW = RX/LNA, HIGH = TX/PA
|
|
CPS -- wired to SX1262 DIO2 (enable DIO2-as-RF-switch)
|
|
```
|
|
|
|
Notes:
|
|
- V4.2 boards use a GC1109 FEM with different control (CSD + CPS, CTX on
|
|
DIO2). Do NOT copy V4.2 configuration.
|
|
- RNode 1.86 auto-detects the FEM by reading CSD as input after powering
|
|
the FEM: KCT8103L pulls HIGH, GC1109 pulls LOW.
|
|
- After TX, CTX must be driven LOW again or the FEM stays in TX-bypass and
|
|
RX is dead (documented failure mode in RTNode sx126x.cpp).
|
|
|
|
## TCXO — DOCUMENTED (RNode 1.86), verified working
|
|
|
|
- DIO3-controlled TCXO, 1.8 V (`SetDIO3AsTCXOCtrl` code 0x02), ~4 ms start.
|
|
- After enabling the TCXO, recalibrate all blocks or `XOSC_START_ERR`
|
|
persists in device errors.
|
|
- OCP register set to 0x28 (RNode 1.86 "OCP_TUNED" for the V4 PA chain).
|
|
|
|
## SDR
|
|
|
|
```
|
|
Nooelec NESDR SMArt v5
|
|
RTL2832U + R820T, USB ID 0bda:2838, serial 33999948
|
|
```
|
|
|
|
### Observer reliability (EXPERIMENTALLY VERIFIED)
|
|
|
|
This dongle is not a stable instrument and every measurement must record
|
|
its state. Three distinct failure modes were observed and characterised:
|
|
|
|
1. **Sensitivity drift.** Within minutes of continuous streaming the tuner
|
|
loses roughly 17 dB. Measured with `hil/sdr_health.py`: fresh after
|
|
replug ~ +22 dB mean power at 42.1 dB gain and ~51 dB spectrum span;
|
|
after a few minutes ~ +5 dB and ~19 dB span. Captures at "the same
|
|
gain" taken minutes apart are therefore NOT comparable.
|
|
2. **Tuner death mid-stream.** `r82xx_write: i2c wr failed` appears and the
|
|
receiver goes deaf, but `rtl_sdr` does NOT exit -- it keeps producing
|
|
nothing. A naive long capture silently returns "no traffic". Observed at
|
|
~192 s into a 1800 s capture. Mitigation: bounded capture segments with
|
|
`-n` plus `usbreset` between them (`hil/capture_both.sh`).
|
|
3. **Descriptor / enumeration faults.** The device can enumerate with empty
|
|
descriptor strings (`rtl_test` prints `0: , , SN: `) or disappear from
|
|
the bus entirely, in which case `usbreset` reports "No such device
|
|
found" and only a physical replug recovers it. Discovery therefore
|
|
identifies the dongle by USB VID:PID 0bda:2838, not descriptor text.
|
|
|
|
`usbreset 0bda:2838` recovers modes 1-3 as long as the device is still
|
|
enumerated. Kernel `over_current_count` stayed 0 throughout, so the port
|
|
never tripped protection; the dongle's own controller hangs.
|
|
|
|
Note: "[R82XX] PLL not locked!" printed while tuning is BENIGN -- it is
|
|
emitted while `rtl_sdr` probes and disables direct-sampling mode, and
|
|
appears on both rtl-sdr-blog and osmocom builds. An earlier revision of
|
|
this document blamed `rtl_test -t` for wedging the tuner; that was
|
|
DISPROVEN. The real symptom of a deaf receiver is railed, gain-independent
|
|
noise, which is what `hil/sdr_health.py` tests for.
|